Skip to content

mltorley

New Contributor

Joined 

November 30th, 2015

About me

No bio added

mltorley's Activities

All Activities
Selected All Activities

mltorley
commented on 's post

9 years ago

Dual-Stack have been enabled on both the SMC D3G CCR and the Cisco DPC3939B..  If you dont have dual-stack reboot your device and the bootfile will enable it..

Does the RA service show it's advertising the correct prefix?  I can do one better - Here's an RA packet I capped with wireshark: Frame 2: 174 bytes on wire (1392 bits), 174 bytes captured (1392 bits) on interface 0Ethernet II, Src: Netgear_ed:1d:32

mltorley
commented on 's post

9 years ago

Dual-Stack have been enabled on both the SMC D3G CCR and the Cisco DPC3939B..  If you dont have dual-stack reboot your device and the bootfile will enable it..

If I can, I'll give it a shot. Things like removing any static addresses will have to wait till I can reboot without causing trouble for the office.

mltorley
commented on 's post

9 years ago

Dual-Stack have been enabled on both the SMC D3G CCR and the Cisco DPC3939B..  If you dont have dual-stack reboot your device and the bootfile will enable it..

Here's the routing table as it is right now. There are artifacts from my last round of attempts, but the routes from the gateway are there.   Interface 12 is WAN, 13 is LAN, 14 and up are VPN, 6-to-4 and direct access interfaces that aren't doi

mltorley
commented on 's post

9 years ago

Dual-Stack have been enabled on both the SMC D3G CCR and the Cisco DPC3939B..  If you dont have dual-stack reboot your device and the bootfile will enable it..

Well, I know there would be problems if the prefix changes (though the gateway does allow me to set a /56, I don't know how static it is), but now I'm determined to make it work.   Windows is getting the default routes from the gateway's RA, includin

mltorley
commented on
mltorley
's post

9 years ago

Okay, Comcast swapped my Cisco for a Netgear as the Cisco doesn't offer functional PD.  The Netgear displays a /56 prefix, but it doesn't delegate.  Network is setup like this:  Gateway  -> Server 2012r2 router/firewall -> office network  Gateway and router have 2601:xx:xxxx:xx00::/64 addresses, off

Thanks, but I've read it.  Looks like the heart of the issue is the gateway's filtering policy.  It rejects packets who's source /64 doesn't match it's /64 when it should be filtering according to the assigned /56.  So, instead of the 265 subnets it

mltorley
posted a question

December 10, 2015

9 years ago

Okay, Comcast swapped my Cisco for a Netgear as the Cisco doesn't offer functional PD.  The Netgear displays a /56 prefix, but it doesn't delegate.  Network is setup like this:  Gateway  -> Server 2012r2 router/firewall -> office network  Gateway and router have 2601:xx:xxxx:xx00::/64 addresses, off

mltorley
commented on 's post

9 years ago

Dual-Stack have been enabled on both the SMC D3G CCR and the Cisco DPC3939B..  If you dont have dual-stack reboot your device and the bootfile will enable it..

@train_wreck wrote: My guess is that the vast majority of customers who purchase "Comcast Business" in the HFC (coaxial-based) form are likely home businesses/small businesses, often with no dedicated IT staff (or a rather small one). Customers who w

mltorley
commented on 's post

9 years ago

Hi, I'm trying to get IPV6 working at a site in Boston. After a bit of troubleshooting, I've determined that my business gateway is firewalling incoming IPV6 traffic.  I can get connectivity to devices that are directly connected to the cable modem by adding them to 'allow ipv6 access from out

I got some helpful answers in this thread - http://forums.businesshelp.comcast.com/t5/IPV6/Dual-Stack-on-SMC-D3GCCR-and-Cisco-DPC3939B/m-p/27797/highlight/false#M552 Looks like getting a useful prefix delegation is only possible with the Netgear gate

mltorley
commented on 's post

9 years ago

Dual-Stack have been enabled on both the SMC D3G CCR and the Cisco DPC3939B..  If you dont have dual-stack reboot your device and the bootfile will enable it..

train_wreck wrote:mltorley wrote:I was just told by Comcast that they have no equipment at all that will properly handle IPv6 and static IP4, and that my only option to get a prefix shorter than /64 was to buy a modem and lose my office's static IP4

mltorley
commented on 's post

9 years ago

If I put my modem into TBM, will I have to configure my personal router? Will it just grab the ip and I can setup functions from it?

Can I add that UPnP functionality on the gateway would be irrelevant in TBM?  Only the firewall/router  needs it enabled, regardless of whether it's builtin to the gateway or a separate personal device.  In TBM, all traffic passes through, regardless